Choosing the right boiler feed pump is not simply a matter of finding a pump that can move enough water. The pump must deliver the required feedwater flow while producing enough pressure to overcome boiler pressure, elevation changes, pipe friction, control valves, economizers, and other system losses check more here : 100+ Boiler Feed Pump Calculation: Formula, Sizing & Calculator .
A proper boiler feed pump sizing calculation helps ensure that the boiler receives a steady supply of water under normal and peak operating conditions. If the pump is too small, the boiler may struggle to maintain its water level when steam demand increases. If it is too large, the system can waste energy, create excessive control-valve throttling, and operate the pump away from its most efficient range.
The main factors involved in boiler feedwater pump sizing include boiler steam capacity, feedwater flow rate, operating pressure, total dynamic head, water temperature, pump efficiency, NPSH, piping losses, and an appropriate design margin.
This guide explains each part of the calculation in simple terms so you can understand how boiler feed pumps are sized and how the different variables affect the final pump selection.

Boiler Feed Pump Sizing Calculator
A boiler feed pump sizing calculator provides a quick way to estimate the flow rate, discharge pressure, pump head, and power required for a boiler feedwater system.
Instead of calculating every value manually, you can enter important operating conditions such as boiler capacity, boiler pressure, feedwater temperature, static head, system losses, and pump efficiency. The calculator then uses these values to estimate the required pump duty.
The calculated result should be treated as an engineering starting point. Final pump selection should also be checked against the manufacturer’s pump curve, NPSH requirements, motor rating, materials, operating temperature, and actual system conditions.
Enter Boiler Operating Data
Accurate pump sizing begins with accurate boiler operating data.
Typical information required includes:
- Maximum steam production
- Boiler operating pressure
- Feedwater temperature
- Feedwater supply pressure
- Suction tank or deaerator pressure
- Static elevation difference
- Pipe friction losses
- Economizer pressure drop
- Control valve pressure drop
- Pump efficiency
- Required operating margin
Using maximum expected operating conditions is usually more useful than sizing the pump only around the average boiler load.
Boiler Steam Capacity
Boiler steam capacity tells you how much steam the boiler can produce during a given period.
It may be expressed as:
- kg/h
- lb/h
- ton/h
- boiler horsepower
- kg/s
Steam production is one of the most important inputs because the boiler must receive enough feedwater to replace the water converted into steam.
For example, if a boiler produces 10,000 kg/h of steam, the basic feedwater requirement will be close to that value before allowances for blowdown, system losses, and design margin are added.
Boiler Operating Pressure
The feed pump must discharge water at a pressure higher than the pressure inside the boiler.
A pump that delivers water at the same pressure as the boiler would normally not provide enough differential pressure to force water through the feedwater line.
The required pump discharge pressure can include:
Boiler pressure + static pressure + piping losses + valve losses + economizer losses + operating margin
This is why boiler pressure alone should never be used as the complete feed pump pressure requirement.
Feedwater Temperature
Feedwater temperature has an important effect on boiler feed pump performance.
Hot feedwater has different density and vapor-pressure characteristics compared with cold water. As water temperature rises, its vapor pressure also rises, increasing the risk of cavitation at the pump suction.
This becomes especially important when the feedwater comes from a deaerator operating close to the saturation temperature.
Feedwater temperature therefore affects both the pump head calculation and the NPSH calculation.
Feedwater Flow Rate
The required feedwater flow normally starts with the boiler’s maximum steam production.
A simplified relationship is:
Feedwater Flow = Steam Flow + Blowdown + Other Water Losses
A design margin may then be added depending on the boiler system and operating requirements.
The pump should be capable of meeting the maximum expected demand rather than only the normal operating flow.
Static Head
Static head is created by the vertical elevation difference between different points in the feedwater system.
For example, if the pump must raise water from a lower feed tank to equipment located at a higher elevation, additional pump head is required.
Static head does not depend on pipe length or water velocity. It mainly depends on the vertical elevation difference and the fluid density.
Pipe and Fitting Losses
As feedwater moves through pipes, elbows, valves, strainers, tees, reducers, and other fittings, friction causes a pressure loss.
The pump must provide enough additional head to overcome these losses.
Friction losses increase significantly when:
- Flow velocity increases
- Pipe diameter decreases
- Pipe length increases
- More fittings are installed
- Control valves create additional resistance
Ignoring piping losses can result in an undersized boiler feed pump even when the calculated boiler pressure appears correct.
Pump Efficiency
No real pump converts all motor power into useful hydraulic energy.
Pump efficiency represents the percentage of input power that becomes useful hydraulic power.
For example, a pump with an efficiency of 75% requires more shaft power than the ideal hydraulic power calculation suggests.
Pump efficiency is therefore needed when calculating the required motor power.
Safety Margin
A reasonable design margin helps the feed pump handle operating variations and peak boiler demand.
However, adding an excessive margin can create another problem: an oversized pump.
An oversized pump may require constant throttling through the feedwater control valve and can operate far away from its best efficiency point.
The goal should be to provide enough margin for reliable operation without unnecessarily increasing pump size.
Calculate Required Pump Capacity
The required pump capacity is mainly determined from the maximum feedwater demand.
A simplified approach is:
Required Pump Flow = Maximum Feedwater Demand × Design Factor
For example, if the calculated feedwater requirement is:
20 m³/h
and the selected design factor is:
1.10
then:
Required Pump Flow = 20 × 1.10
Required Pump Flow = 22 m³/h
This means the pump should be capable of delivering approximately 22 m³/h at the calculated system head.
Flow alone is not enough to select the pump. The required head must also be known.
Boiler Feed Pump Calculation Results
A useful boiler feed pump calculation should provide several results rather than only one pump size.
Typical outputs include:
- Required feedwater flow
- Recommended design flow
- Required discharge pressure
- Total dynamic head
- Hydraulic power
- Estimated shaft power
- Estimated motor power
- NPSH available
- Suggested pump duty point
These values provide the basis for comparing the calculated duty against an actual manufacturer’s pump curve.
What Is Boiler Feed Pump Sizing?
Boiler feed pump sizing is the engineering process used to determine how much water a feed pump must deliver and how much pressure or head it must generate to supply a boiler safely and reliably.
A boiler continuously converts water into steam. That water must be replaced through the feedwater system.
The feed pump therefore has two major responsibilities:
- Deliver enough feedwater to match boiler demand.
- Produce enough pressure to push that water into the pressurized boiler.
This sounds simple, but several system conditions affect both requirements.
The pump may need to overcome:
- Boiler drum pressure
- Static elevation
- Feedwater piping friction
- Check valves
- Control valves
- Economizers
- Flow meters
- Strainers
- Other feedwater equipment
The final pump selection must satisfy both flow and head at the same operating point.
Purpose of a Boiler Feedwater Pump
The main purpose of a boiler feedwater pump is to move treated feedwater from a feed tank or deaerator into the boiler.
Because the boiler operates under pressure, the pump must raise the water pressure high enough for the water to enter the boiler.
In many industrial boiler systems, the feedwater pump operates continuously while a feedwater control valve or variable-speed system adjusts the actual flow according to boiler demand.
A properly sized pump helps maintain stable boiler water level and supports reliable steam production.
Why Correct Feed Pump Sizing Matters
Correct sizing affects reliability, efficiency, operating cost, and boiler performance.
An undersized pump may fail to supply enough water during peak steam demand. This can contribute to low-water-level conditions and boiler shutdowns.
An oversized pump can create problems such as excessive valve throttling, higher power consumption, increased vibration, unstable control, and operation far from the pump’s best efficiency point.
A well-sized boiler feed pump should provide the required capacity while operating within a suitable region of its performance curve.
Boiler Feed Pump vs Regular Water Pump
A boiler feed pump operates under more demanding conditions than many ordinary water pumps.
Boiler feed pumps may need to handle:
- High discharge pressure
- Elevated water temperature
- Continuous operation
- Significant pressure fluctuations
- High differential head
- Low available suction margin
- Strict reliability requirements
High-pressure boiler systems commonly use multistage centrifugal pumps because multiple impellers can develop a much higher total head than a typical single-stage pump.
How a Feed Pump Supplies Water Against Boiler Pressure
Water only flows into the boiler when the feedwater pressure is greater than the pressure resisting the flow.
If the boiler operates at 10 bar, for example, the pump cannot simply be selected for 10 bar discharge pressure.
Additional pressure may be needed to overcome:
- Pipe friction
- Static elevation
- Economizer resistance
- Feedwater control valve pressure drop
- Check valve resistance
- Other system losses
The required pump discharge pressure must therefore be greater than the boiler operating pressure.
Boiler Feed Pump Sizing Calculation at a Glance
The complete sizing process can be understood through a few major engineering steps.
First, calculate how much feedwater the boiler needs.
Next, determine how much pressure the pump must overcome.
Then convert the system pressure requirements into total pump head where necessary.
After that, verify that the pump has sufficient suction conditions by checking NPSH.
Finally, calculate the required pump and motor power and compare the resulting duty point with a real pump performance curve.
Required Feedwater Flow
Required feedwater flow begins with the maximum steam production rate.
A simplified expression is:
Feedwater Requirement = Steam Production + Boiler Blowdown + System Losses
A suitable operating margin can then be included.
If condensate is returned to the boiler plant, it affects makeup-water demand, but the feed pump still needs to handle the feedwater flow required by the boiler under its design operating condition.
Required Discharge Pressure
The required discharge pressure depends on the resistance downstream of the pump.
A simplified relationship is:
Pump Discharge Pressure = Boiler Pressure + Static Pressure + Equipment Pressure Drop + Piping Losses + Required Control Differential
Each system is different, which is why using only boiler operating pressure can underestimate the required pump duty.
Required Total Dynamic Head
Total dynamic head, commonly abbreviated as TDH, represents the total energy per unit weight that the pump must add to the fluid.
For a boiler feedwater system, TDH may include:
Pressure Head + Static Head + Friction Head + Equipment Losses
The final head is normally expressed in:
- meters of liquid
- feet of liquid
The calculated flow and TDH together create the basic pump duty point.
Required Pump Power
Once flow and head are known, the hydraulic power can be estimated.
For SI units, a commonly used relationship is:
Hydraulic Power (kW) = ρ × g × Q × H / 1000
Where:
ρ = fluid density in kg/m³
g = gravitational acceleration in m/s²
Q = flow rate in m³/s
H = pump head in meters
Because a real pump is not 100% efficient, the required shaft power is higher than the hydraulic power.
Therefore:
Shaft Power = Hydraulic Power ÷ Pump Efficiency
Motor selection should then account for the actual pump performance and suitable motor margin.
Required NPSH Margin
NPSH is especially important in boiler feed pump applications because the feedwater may be very hot.
NPSHA, or Net Positive Suction Head Available, describes the suction energy available in the actual system.
NPSHR, or Net Positive Suction Head Required, is provided by the pump manufacturer for a particular operating condition.
For reliable operation:
NPSHA should be greater than NPSHR with an appropriate engineering margin.
If sufficient suction head is not available, the water may begin to vaporize locally inside the pump, creating cavitation.
Recommended Operating Margin
A pump should have enough capacity to deal with expected operating variation, but a large arbitrary safety factor is not always better.
Too much additional flow or head can move the operating point away from the pump’s best efficiency region.
A better approach is to calculate the system requirement carefully, apply a justified margin, and then select a pump whose curve matches the expected duty.
Boiler Feed Pump Sizing Formula
There is no single formula that completely sizes a boiler feed pump.
Pump sizing normally combines several calculations covering:
- Feedwater flow
- Boiler pressure
- Total dynamic head
- NPSH
- Hydraulic power
- Pump efficiency
- Motor power
The final pump is then selected by matching those calculated requirements with the manufacturer’s performance data.
Basic Boiler Feed Pump Capacity Formula
A simplified capacity calculation can be written as:
Pump Capacity = Required Feedwater Flow × Design Factor
If the boiler requires 30 m³/h and a design factor of 1.10 is applied:
Pump Capacity = 30 × 1.10
Pump Capacity = 33 m³/h
The pump would therefore need to provide approximately 33 m³/h at the required total dynamic head.
The design factor should not be selected blindly. Boiler operation, control philosophy, standby arrangement, maximum load, and applicable engineering requirements should all be considered.
Feedwater Flow Rate Formula
A more useful feedwater relationship is:
Feedwater Flow = Steam Flow + Blowdown Flow + Other Continuous Losses
If blowdown is represented as a fraction of steam generation, the calculation can also be developed from the boiler’s mass balance.
For example:
Steam production = 10,000 kg/h
Blowdown = 300 kg/h
Then:
Feedwater Flow = 10,000 + 300
Feedwater Flow = 10,300 kg/h
Additional justified margin can then be added for pump selection.
Boiler Horsepower to Feedwater Flow Formula
Some boilers are rated in boiler horsepower, especially in applications using Imperial units.
Boiler horsepower can first be converted into an approximate steam-generation rate, after which the feedwater requirement can be calculated.
The correct conversion should be based on the rating definition and design basis being used rather than relying on an arbitrary pump-size rule.
After estimating the steam-production rate:
Required Feedwater = Steam Production + Blowdown + Applicable Losses
The resulting mass flow can then be converted into GPM or m³/h using the feedwater density.
Steam Flow to Feedwater Flow Formula
For a steady-state mass balance:
Feedwater Mass Flow = Steam Mass Flow + Blowdown Mass Flow
For example:
Steam flow = 15,000 kg/h
Blowdown = 450 kg/h
Therefore:
Feedwater Flow = 15,450 kg/h
If the water density at the actual feedwater temperature is known, the mass flow can then be converted into volumetric flow.
The relationship is:
Volumetric Flow = Mass Flow ÷ Density
This conversion matters because pump curves normally display volumetric flow rather than mass flow.
Pump Head Formula
A simplified total head expression is:
TDH = Pressure Head + Static Head + Friction Head + Equipment Losses
For a boiler feedwater system, the pressure head required to overcome boiler pressure is often the largest component.
However, the remaining losses can still be significant, especially when an economizer, control valve, long piping network, or restrictive fittings are present.
Pressure-to-Head Conversion Formula
Pressure and head are related through fluid density.
In SI form:
H = ΔP / (ρg)
Where:
H = head in meters
ΔP = pressure difference in pascals
ρ = fluid density in kg/m³
g = gravitational acceleration
This relationship is important because pump manufacturers normally specify centrifugal-pump performance in terms of head rather than discharge pressure alone.
Pump Hydraulic Power Formula
The hydraulic power required by the fluid can be calculated as:
P = ρgQH
For power in kilowatts:
Hydraulic Power (kW) = ρgQH / 1000
This represents the useful energy transferred to the water.
Actual shaft power will be greater because of pump losses.
Motor Power Calculation Formula
After calculating hydraulic power, pump efficiency can be included:
Pump Shaft Power = Hydraulic Power ÷ Pump Efficiency
For example, if:
Hydraulic power = 30 kW
Pump efficiency = 75% or 0.75
Then:
Shaft Power = 30 ÷ 0.75
Shaft Power = 40 kW
The final motor rating should then be selected using the actual pump curve, expected operating range, motor characteristics, and appropriate engineering margin rather than simply selecting the exact calculated value.
Boiler Feed Pump Sizing Calculation Variables
A reliable boiler feed pump sizing calculation depends on using the right design variables. Even a small error in flow, pressure, temperature, or system loss can change the final pump selection.
The most important variables are boiler capacity, steam generation rate, feedwater temperature, boiler operating pressure, suction conditions, static head, friction loss, pump efficiency, and design margin.
Understanding these values makes it much easier to select a pump that can operate safely across the boiler’s expected load range.
Boiler Capacity
Boiler capacity describes how much steam a boiler can produce.
It may be expressed in:
- kg/h
- lb/h
- ton/h
- boiler horsepower
- MW thermal
This value is often the starting point for calculating the required feedwater flow.
A larger boiler generally requires a larger feedwater pump, but capacity alone is not enough to determine the final pump size.
The operating pressure, piping arrangement, feedwater temperature, and system losses also matter.
Steam Generation Rate
Steam generation rate represents the actual mass of steam produced by the boiler during a given period.
If a boiler produces:
8,000 kg/h of steam
then at least approximately the same mass of water must be returned to the boiler before accounting for blowdown and other losses.
A simplified relationship is:
Feedwater Flow = Steam Generation + Blowdown + Other Losses
For pump sizing, maximum continuous steam generation is normally more important than average steam production.
Boiler Operating Pressure
Boiler operating pressure has a major effect on pump head.
The feed pump must produce enough discharge pressure to overcome the internal boiler pressure as well as additional system resistance.
For example, a boiler operating at 12 bar does not necessarily require a feed pump that produces only 12 bar.
The pump may also need to overcome:
- Static elevation
- Economizer resistance
- Control valve pressure drop
- Pipe friction
- Check valve pressure drop
- Flow-meter resistance
This is why the actual required pump discharge pressure is normally higher than boiler operating pressure.
Feedwater Density
Feedwater density is required when converting mass flow into volumetric flow.
The relationship is:
Volumetric Flow = Mass Flow ÷ Density
Water density changes with temperature.
Cold water is denser than hot water, so the same mass flow can occupy a slightly different volume depending on feedwater temperature.
This matters because pump curves are usually based on volumetric flow such as:
- m³/h
- L/s
- GPM
Using the correct feedwater density improves the accuracy of the calculation.
Feedwater Temperature
Feedwater temperature affects more than water density.
It also affects:
- Vapor pressure
- NPSH available
- Cavitation risk
- Pump suction conditions
- Hydraulic calculations
Hot boiler feedwater is often supplied from a deaerator.
Because deaerated water may be close to its saturation temperature, even a relatively small pressure drop on the pump suction side can create vapor bubbles.
For this reason, feedwater temperature becomes especially important during the NPSH calculation.
Suction Pressure
Suction pressure describes the pressure available at the inlet of the boiler feed pump.
It may come from:
- Atmospheric pressure
- A pressurized deaerator
- Static liquid level
- Tank pressure
- Suction piping conditions
Higher suction pressure generally improves NPSH available.
Low suction pressure increases the possibility of cavitation, particularly when pumping hot water.
Discharge Pressure
Discharge pressure is the pressure produced at the outlet of the pump.
The required discharge pressure must be high enough to overcome all downstream resistance.
A simplified relationship can be written as:
Required Discharge Pressure = Boiler Pressure + System Pressure Losses + Static Pressure Requirement
The exact result depends on how the feedwater system is arranged.
Static Elevation
Static elevation is the vertical height difference between the suction source and the final discharge point.
If the pump has to lift water upward, this elevation increases the required pump head.
If the suction tank is positioned above the pump, the liquid level may instead provide useful suction head.
Elevation should always be considered when calculating both:
- Total dynamic head
- NPSH available
Friction Loss
Water loses energy as it moves through pipes and fittings.
This loss is called friction loss.
Typical sources include:
- Straight pipe
- Elbows
- Tees
- Reducers
- Check valves
- Isolation valves
- Strainers
- Flow meters
- Control valves
Friction loss increases as flow velocity rises.
This is why an undersized pipe can increase the required pump head significantly.
Pump Efficiency
Pump efficiency describes how effectively the pump converts shaft power into hydraulic energy.
A pump with higher efficiency needs less input power to provide the same hydraulic duty.
Efficiency normally changes across the pump curve.
A pump may be most efficient near its best efficiency point, commonly called BEP.
This is one reason why selecting a pump only by maximum flow and maximum head is not enough.
The expected operating point should also be checked against the manufacturer’s curve.
Flow Safety Factor
A flow safety factor or design margin may be added to account for operating variation.
A simplified formula is:
Design Flow = Calculated Feedwater Flow × Design Factor
For example:
Calculated flow = 25 m³/h
Design factor = 1.10
Then:
Design Flow = 25 × 1.10
Design Flow = 27.5 m³/h
The margin should be reasonable rather than excessive.
Adding too much margin can create an oversized pump and inefficient operation.
How to Calculate Boiler Feedwater Flow Rate
The first major step in boiler feed pump sizing is determining how much feedwater the boiler needs.
This calculation normally begins with the maximum steam production rate.
From there, additional water requirements such as boiler blowdown and continuous losses are included.
Determine Maximum Steam Production
Start with the maximum amount of steam the boiler is expected to produce.
For example:
Maximum Steam Production = 12,000 kg/h
This represents the water leaving the boiler as steam.
Under steady operating conditions, that mass must eventually be replaced with feedwater.
Account for Blowdown
Boiler blowdown removes water from the boiler to control dissolved solids and maintain acceptable water chemistry.
Because blowdown water leaves the boiler system, the feed pump must replace it.
A simple mass-balance equation is:
Feedwater Flow = Steam Flow + Blowdown Flow
For example:
Steam flow = 12,000 kg/h
Blowdown = 360 kg/h
Then:
Feedwater Flow = 12,000 + 360
Feedwater Flow = 12,360 kg/h
Account for Feedwater Losses
Some systems may have additional continuous water losses.
These can include losses associated with:
- Sampling
- Drain systems
- Flash systems
- Leakage
- Process requirements
Only real and justified losses should be added.
Artificially inflating losses can lead to unnecessary pump oversizing.
Add Appropriate Flow Margin
After determining the actual feedwater requirement, a design margin may be applied.
Suppose:
Required feedwater = 12,360 kg/h
Design factor = 1.10
Then:
Design Feedwater Flow = 12,360 × 1.10
Design Feedwater Flow = 13,596 kg/h
This becomes the preliminary feed pump design flow.
Determine Final Design Flow Rate
Pump curves normally use volumetric flow rather than mass flow.
Therefore, the calculated feedwater mass flow should be converted using water density.
The equation is:
Q = m ÷ ρ
Where:
Q = volumetric flow
m = mass flow
ρ = feedwater density
If:
Mass flow = 13,596 kg/h
Feedwater density = 960 kg/m³
Then:
Q = 13,596 ÷ 960
Q ≈ 14.16 m³/h
The preliminary design flow is therefore approximately:
14.2 m³/h
This value should then be used together with the required head when selecting the pump.
Boiler Feedwater Flow Rate Formula
Several forms of the feedwater flow equation can be used depending on what information is available.
The most common approach is based on a mass balance around the boiler.
Feedwater Flow Based on Steam Output
For a simple boiler system with no blowdown:
Feedwater Mass Flow ≈ Steam Mass Flow
If a boiler produces:
5,000 kg/h of steam
then approximately:
5,000 kg/h of feedwater
must enter the boiler under steady-state conditions.
In a real plant, additional water is normally required because of blowdown and operating losses.
Feedwater Flow Including Blowdown
When blowdown flow is known directly:
Feedwater Flow = Steam Flow + Blowdown Flow
Example:
Steam flow = 10,000 kg/h
Blowdown = 400 kg/h
Then:
Feedwater Flow = 10,400 kg/h
If blowdown is given as a percentage of steam production:
Blowdown Flow = Steam Flow × Blowdown Fraction
For example:
Steam flow = 10,000 kg/h
Blowdown = 4%
Then:
Blowdown Flow = 10,000 × 0.04
Blowdown Flow = 400 kg/h
So:
Feedwater Flow = 10,400 kg/h
Feedwater Flow Including Design Margin
After calculating the operating requirement:
Design Feedwater Flow = Actual Feedwater Flow × Design Factor
Example:
Actual feedwater flow = 10,400 kg/h
Design factor = 1.10
Then:
Design Feedwater Flow = 11,440 kg/h
This becomes the design basis for pump flow selection.
Example Feedwater Flow Calculation
Consider a boiler with the following conditions:
Steam production = 20,000 kg/h
Blowdown rate = 3% of steam production
Design margin = 10%
First calculate blowdown:
Blowdown = 20,000 × 0.03
Blowdown = 600 kg/h
Then calculate total operating feedwater:
Feedwater = 20,000 + 600
Feedwater = 20,600 kg/h
Now apply the design margin:
Design Feedwater = 20,600 × 1.10
Design Feedwater = 22,660 kg/h
If feedwater density is approximately 970 kg/m³:
Volumetric Flow = 22,660 ÷ 970
Volumetric Flow ≈ 23.36 m³/h
The preliminary boiler feed pump design flow is therefore approximately:
23.4 m³/h
How Much Safety Margin Should Be Added to Pump Capacity?
Safety margin is an important part of pump sizing, but it should be based on engineering judgment rather than simply adding a very large percentage.
The purpose of margin is to account for realistic variations in operating conditions.
It should not be used to compensate for incomplete calculations.
Why Pump Capacity Margin Is Needed
Actual boiler demand rarely stays perfectly constant.
Steam consumption may increase because of:
- Process changes
- Startup conditions
- Load swings
- Control variation
- Temporary peak demand
A suitable margin gives the feed pump enough additional capacity to manage these conditions.
Difference Between Design Flow and Normal Flow
Normal flow represents the typical operating requirement.
Design flow represents the capacity used for equipment selection.
For example:
Normal feedwater flow = 30 m³/h
Design flow = 33 m³/h
The additional 3 m³/h provides operating flexibility.
The pump should still operate efficiently at both normal and design conditions.
Risks of Oversizing the Feedwater Pump
A very large margin can result in an oversized pump.
Common consequences include:
- Excessive throttling
- Higher energy consumption
- Increased control valve pressure drop
- Operation far from BEP
- Increased vibration
- More wear on pump components
- Poor drum-level control
Oversizing also increases equipment and motor cost.
Risks of Undersizing the Feedwater Pump
An undersized feed pump may work adequately at normal boiler load but fail when steam demand rises.
Possible problems include:
- Falling boiler water level
- Low-water alarms
- Boiler trips
- Inability to maintain steam production
- Continuous operation near maximum pump capacity
- Reduced operational flexibility
A proper design margin helps avoid these problems without creating unnecessary oversizing.
How to Calculate Boiler Feed Pump Pressure
After determining flow, the next step is calculating how much pressure the boiler feed pump must produce.
The pump discharge pressure must be higher than the total resistance downstream of the pump.
Boiler Operating Pressure
Boiler operating pressure is normally the largest pressure that the feedwater pump must overcome.
Suppose the boiler operates at:
10 bar gauge
The pump discharge pressure must exceed this value before feedwater can enter the boiler.
But boiler pressure is only one part of the total requirement.
Pressure Required to Enter the Boiler
Feedwater must flow from a higher pressure toward the boiler.
Therefore, a differential pressure is required between the feedwater line and the boiler.
If pump discharge pressure were exactly equal to boiler pressure, there would be little or no driving force for flow once system resistance is considered.
Economizer Pressure Drop
If an economizer is installed between the pump and boiler, it creates additional resistance.
Suppose:
Boiler pressure = 10 bar
Economizer pressure drop = 0.8 bar
The pump already needs more than:
10.8 bar
before considering piping, valves, and elevation.
Control Valve Pressure Drop
A modulating feedwater control valve requires a pressure differential to regulate flow effectively.
For example:
Boiler pressure = 10 bar
Economizer loss = 0.8 bar
Control valve pressure drop = 1.2 bar
Then the required pressure becomes at least:
12 bar
before adding other system losses.
Feedwater Piping Pressure Loss
The piping system adds further resistance.
Suppose:
Pipe and fitting loss = 0.5 bar
Then:
Required Pressure = 10 + 0.8 + 1.2 + 0.5
Required Pressure = 12.5 bar
Static elevation may also need to be included.
Required Pump Discharge Pressure
A simplified equation is:
Pump Discharge Pressure = Boiler Pressure + Static Pressure + Pipe Loss + Equipment Loss + Control Valve Differential
For example:
Boiler pressure = 12 bar
Static pressure requirement = 0.4 bar
Pipe loss = 0.6 bar
Economizer loss = 0.7 bar
Control valve differential = 1.0 bar
Then:
Pump Discharge Pressure = 12 + 0.4 + 0.6 + 0.7 + 1.0
Pump Discharge Pressure = 14.7 bar
This is a much more realistic sizing basis than selecting a pump for only 12 bar.
Boiler Feed Pump Head Calculation
Centrifugal pumps are usually selected using head rather than pressure.
Pump head represents the energy that the pump adds to the liquid.
This is why the calculated system pressure must often be converted into meters or feet of head.
What Is Pump Head?
Pump head represents the height of a liquid column that corresponds to a certain amount of energy.
Common units are:
- meters of liquid
- feet of liquid
Head is especially useful because centrifugal pump performance is naturally expressed this way.
Static Suction Head
Static suction head exists when the liquid level in the feedwater tank or deaerator is above the pump centerline.
This helps push water into the pump.
Greater static suction head generally improves pump suction conditions and can increase NPSH available.
Static Discharge Head
Static discharge head is the vertical elevation difference from the pump to the downstream discharge point.
If the pump must raise water upward, this height adds to the required total head.
Friction Head Loss
Friction head is the energy lost as water moves through the piping system.
It depends on:
- Pipe diameter
- Pipe length
- Flow rate
- Pipe roughness
- Number of fittings
- Valve type
Higher flow normally increases friction loss.
Boiler Pressure Head
Boiler pressure can be converted into equivalent liquid head using:
H = ΔP ÷ ρg
This pressure-head term is often the largest part of the total dynamic head in a high-pressure boiler feedwater system.
Equipment Pressure Drop
Equipment installed in the feedwater line can create significant pressure loss.
Examples include:
- Economizers
- Control valves
- Flow meters
- Strainers
- Check valves
- Heat exchangers
These losses should be converted into equivalent head and included in the total pump calculation.
Total Dynamic Head Calculation
A simplified boiler feed pump TDH equation is:
TDH = Boiler Pressure Head + Static Head + Friction Head + Equipment Loss Head
For example:
Boiler pressure head = 125 m
Static head = 8 m
Pipe friction = 7 m
Economizer and valve losses = 18 m
Then:
TDH = 125 + 8 + 7 + 18
TDH = 158 m
The pump should therefore be evaluated around the required design flow at approximately 158 meters of total head, subject to final system and manufacturer checks.
Total Dynamic Head Formula for Boiler Feed Pumps
Total dynamic head combines every major resistance that the pump must overcome.
A more complete expression can be written as:
TDH = Pressure Head + Static Head + Pipe Friction Head + Valve Losses + Equipment Losses
Each term should be calculated using the actual operating conditions of the system.
Static Head
Static head is based on elevation difference.
If the boiler feedwater enters a point 10 meters above the pump, approximately 10 meters of static discharge head must be considered.
If the deaerator water level is above the pump suction, that elevation can provide positive suction head.
Boiler Pressure Head
Boiler pressure head is found by converting pressure to equivalent liquid head.
For water, a rough conversion at moderate temperatures is sometimes used during preliminary calculations.
However, for accurate boiler feed pump sizing, actual fluid density at feedwater temperature should be used.
Pipe Friction Loss
Pipe friction should be calculated at the design flow rate.
This is important because friction loss changes with flow.
A system calculated at normal flow may have noticeably higher friction loss at maximum design flow.
Valve and Fitting Losses
Elbows, tees, valves, strainers, and other components add resistance.
These can be calculated using either:
- Loss coefficients
- Equivalent pipe length
All relevant components between pump discharge and boiler entry should be considered.
Economizer Loss
An economizer can create a noticeable pressure drop, particularly at high feedwater flow.
Manufacturer pressure-drop data should be used where available.
The pressure drop should be converted into equivalent head and added to the TDH.
Control Valve Loss
A control valve requires sufficient differential pressure to regulate feedwater.
If too little differential pressure is available, the valve may lose control authority.
If too much is available, energy may be wasted through unnecessary throttling.
The design should therefore balance pump head and control-valve requirements.
Final TDH Calculation
Consider this example:
Boiler pressure head = 140 m
Static head = 12 m
Pipe friction = 9 m
Economizer loss = 11 m
Control valve loss = 15 m
Other equipment loss = 3 m
Then:
TDH = 140 + 12 + 9 + 11 + 15 + 3
TDH = 190 m
The preliminary pump duty point might therefore be stated as:
Design Flow: 25 m³/h
Design Head: 190 m
These two values can then be compared with available pump performance curves.
Converting Boiler Pressure to Pump Head
Boiler pressure is usually given in units such as bar, psi, or kPa, while centrifugal pump performance is normally shown as meters or feet of head.
Because of this, pressure often needs to be converted into head before a boiler feed pump can be selected.
The basic relationship is:
Head = Pressure ÷ Fluid Density × Gravity
In SI form:
H = ΔP / (ρg)
Where:
H = head in meters
ΔP = pressure difference in pascals
ρ = fluid density in kg/m³
g = gravitational acceleration in m/s²
This calculation becomes more important when feedwater is hot because hot water has a lower density than cold water.
PSI to Feet of Head
For water near standard conditions, a commonly used approximation is:
1 psi ≈ 2.31 ft of water
So if a pump must overcome:
100 psi
the approximate pressure head is:
100 × 2.31 = 231 ft
This is useful for quick Imperial calculations.
However, for hot boiler feedwater, using actual fluid density gives a more accurate result.
Bar to Meter of Head
For water near standard conditions:
1 bar ≈ 10.2 meters of water
For example:
Boiler pressure = 12 bar
Approximate pressure head:
12 × 10.2 = 122.4 m
If the system also has 25 meters of additional losses:
Total Head = 122.4 + 25
Total Head = 147.4 m
The feed pump would therefore need to provide approximately 147 meters of head at the required flow rate.
kPa to Meter of Head
A useful approximation for water is:
1 meter of water ≈ 9.81 kPa
Therefore:
Head in meters = Pressure in kPa ÷ 9.81
If the required differential pressure is:
1,000 kPa
then:
Head = 1,000 ÷ 9.81
Head ≈ 101.9 m
Again, fluid density should be considered if higher accuracy is required.
Effect of Feedwater Density on Head
Head and pressure are related, but they are not exactly the same thing.
For a given pressure difference, the required head changes with fluid density.
Hot water is less dense than cold water.
This means the same pressure can correspond to a slightly greater head when the water temperature is high.
That difference may be small in some systems but important in high-pressure boiler applications.
Why Hot Feedwater Changes Pump Calculations
Hot feedwater affects several parts of pump sizing at the same time.
It changes:
- Fluid density
- Vapor pressure
- NPSH available
- Cavitation risk
- Volumetric flow
- Pressure-to-head conversion
This is why boiler feed pump calculations should use the actual feedwater temperature whenever possible instead of assuming room-temperature water.
Feedwater Temperature and Pump Sizing
Feedwater temperature is one of the most important variables in boiler feed pump selection.
A feed pump handling cold makeup water operates under very different suction conditions than a pump receiving hot water from a deaerator.
As the feedwater temperature rises, the liquid moves closer to its boiling point for the available suction pressure.
That reduces the margin against cavitation.
Cold Feedwater
Cold feedwater generally provides more favorable suction conditions.
Because its vapor pressure is low, there is a larger pressure margin before the water begins to vaporize.
This usually means:
- Higher NPSH available
- Lower cavitation risk
- Easier pump suction conditions
However, cold water is not always desirable from the boiler-system perspective because feedwater heating improves boiler efficiency and can reduce thermal stress.
Hot Feedwater
Hot feedwater is common in industrial steam systems.
Heating the water before it enters the boiler reduces the amount of energy the boiler must add.
However, hot feedwater creates a more demanding pump suction condition.
As water temperature increases, vapor pressure rises.
If suction pressure drops too low, part of the liquid may flash into vapor inside the pump.
Deaerated Feedwater
A deaerator removes dissolved oxygen and other gases from boiler feedwater while also heating the water.
The feedwater leaving a deaerator is often close to saturation temperature.
This creates an important pump-design challenge.
The pump needs enough positive suction head to prevent flashing and cavitation.
For this reason, boiler feed pumps are often installed below the deaerator so that elevation creates additional static suction head.
Effect of Temperature on Water Density
Water density decreases as temperature rises.
Suppose the required mass flow is:
20,000 kg/h
At a density of:
1,000 kg/m³
the volumetric flow is:
20 m³/h
If the water density falls to:
960 kg/m³
then:
Volumetric Flow = 20,000 ÷ 960
Volumetric Flow ≈ 20.83 m³/h
The same mass of water therefore requires a slightly higher volumetric pump capacity.
Effect of Temperature on Vapor Pressure
Vapor pressure increases rapidly as water temperature rises.
This is critical because NPSH calculations include the vapor-pressure head of the liquid.
A higher vapor pressure reduces NPSH available.
This is one reason boiler feed pumps can experience cavitation even when the suction piping looks adequate.
Why Temperature Matters for Cavitation
Cavitation occurs when local pressure inside the pump falls below the vapor pressure of the liquid.
Small vapor bubbles form and then collapse as they move into higher-pressure regions.
This can cause:
- Noise
- Vibration
- Loss of performance
- Impeller damage
- Seal problems
- Reduced pump life
Hot boiler feedwater is especially sensitive to this problem.
NPSH Calculation for Boiler Feed Pumps
NPSH stands for Net Positive Suction Head.
It is one of the most important checks in boiler feed pump sizing.
Two values are commonly used:
NPSHA = Net Positive Suction Head Available
NPSHR = Net Positive Suction Head Required
NPSHA comes from the system.
NPSHR comes from the pump manufacturer.
The available value should remain greater than the required value with a suitable margin.
What Is NPSH?
NPSH describes how much suction pressure exists above the vapor pressure of the liquid.
In simple terms, it tells you whether enough pressure is available at the pump inlet to keep the feedwater in liquid form.
If the available suction energy becomes too low, cavitation can occur.
NPSH Available
NPSHA is determined by the actual installation.
It can be affected by:
- Tank pressure
- Atmospheric pressure
- Deaerator pressure
- Liquid level
- Suction pipe losses
- Feedwater temperature
- Vapor pressure
- Pump elevation
A simplified relationship can be written as:
NPSHA = Pressure Head at Liquid Surface + Static Suction Head − Suction Friction Loss − Vapor Pressure Head
The exact equation depends on whether the tank is open or pressurized.
NPSH Required
NPSHR is a pump characteristic.
It is determined through pump testing and shown on the manufacturer’s performance curve.
NPSHR changes with flow rate.
In many pumps, the required NPSH increases as flow increases.
This is why NPSH must be checked at the intended operating point, not only at one arbitrary condition.
NPSHA Formula
For a simplified open-tank system:
NPSHA = Atmospheric Head + Static Suction Head − Suction Friction Head − Vapor Pressure Head
For a pressurized deaerator:
NPSHA = Tank Pressure Head + Static Suction Head − Suction Friction Head − Vapor Pressure Head
Each term should be calculated using consistent units.
Atmospheric Pressure
If the feedwater tank is open to atmosphere, atmospheric pressure contributes to NPSH available.
Atmospheric pressure decreases as elevation above sea level increases.
This means a pump installation at high altitude can have less NPSHA than the same installation near sea level.
Suction Tank Pressure
A pressurized deaerator can provide additional pressure at the pump suction.
However, because deaerator water is usually hot and close to saturation, much of that pressure may be offset by the high vapor pressure of the water.
This is why deaerator elevation often plays such an important role.
Vapor Pressure of Hot Feedwater
Vapor pressure must be included in the NPSH calculation.
As temperature increases, vapor pressure rises and reduces the available suction margin.
Ignoring vapor pressure is one of the most serious mistakes that can be made in hot-water pump sizing.
Suction Pipe Friction Loss
Pressure is lost as water travels through the suction pipe.
Common causes include:
- Long suction piping
- Small pipe diameter
- Elbows
- Strainers
- Isolation valves
- Reducers
- High flow velocity
Because boiler feed pumps may operate with limited NPSH margin, suction piping should normally be designed with low resistance.
NPSH Safety Margin
It is not enough for NPSHA to be only slightly higher than NPSHR.
A suitable margin should be maintained to account for:
- Flow variation
- Temperature changes
- Pump wear
- Instrument uncertainty
- Fouling
- Changes in suction level
The required margin should be selected according to pump design, manufacturer guidance, service criticality, and applicable engineering practice.
How to Prevent Cavitation in a Boiler Feed Pump
Cavitation can seriously damage a boiler feed pump.
The best approach is to design the suction system so that adequate NPSH is available under the worst expected operating conditions.
Increase Suction Head
One of the most effective solutions is increasing the vertical distance between the feedwater level and the pump suction.
Installing the pump below the deaerator creates positive static suction head.
More elevation means more pressure at the pump inlet.
Reduce Suction-Line Pressure Loss
The suction pipe should have low resistance.
Possible improvements include:
- Increasing pipe diameter
- Reducing unnecessary fittings
- Using long-radius elbows
- Keeping the suction run short
- Keeping strainers clean
- Avoiding partially closed valves
These changes help preserve pressure at the pump inlet.
Maintain Correct Deaerator Level
A falling deaerator water level reduces static suction head.
If the liquid level drops too far, NPSHA can decrease enough to create cavitation.
Maintaining the correct operating level is therefore important for both boiler operation and pump reliability.
Control Feedwater Temperature
Higher feedwater temperature increases vapor pressure.
If water temperature becomes higher than the design condition, NPSH margin may decrease.
The actual operating temperature should therefore be considered when selecting and troubleshooting the pump.
Select a Pump With Suitable NPSHR
Different pump designs can have different NPSH requirements.
When suction conditions are difficult, selecting a pump with lower NPSHR may improve reliability.
The comparison should be made at the actual intended duty point.
Avoid Excessive Pump Speed
Higher pump speed can increase NPSH requirement.
In some cases, running a pump faster than necessary can increase cavitation risk.
Pump speed should therefore be considered together with flow, head, and suction conditions.
Deaerator and Boiler Feed Pump Sizing
The deaerator has a major influence on boiler feed pump design because it often serves as the pump’s suction source.
Its pressure, temperature, elevation, and water level all affect the available suction head.
Deaerator Pressure
A deaerator normally operates above atmospheric pressure.
This positive vessel pressure contributes to pressure at the pump suction.
However, the water is also very hot.
Because it is close to saturation temperature, vapor pressure is high.
Both values must be included in the NPSH calculation.
Deaerator Elevation
Elevation is one of the most important design features in a boiler feedwater system.
The pump is often installed below the deaerator so gravity can provide positive suction pressure.
For example, if the deaerator water level is:
8 meters above the pump centerline
then approximately 8 meters of static suction head is available before considering other factors.
This additional head can be essential for preventing cavitation.
Feedwater Temperature at Pump Suction
The actual pump suction temperature should be used in NPSH calculations.
Using a lower assumed temperature can make the available NPSH appear better than it really is.
For accurate design, use the expected maximum feedwater temperature at the pump inlet.
Available Suction Head
Available suction head depends on the complete suction arrangement.
It may include:
Deaerator Pressure Head + Static Liquid Head − Suction Friction Loss
But the water vapor pressure must also be subtracted when calculating NPSHA.
Deaerator-to-Pump NPSH Calculation
Suppose a simplified system has:
Deaerator pressure head above vapor pressure = 2.5 m
Static elevation head = 9 m
Suction friction loss = 1.2 m
Then:
NPSHA = 2.5 + 9 − 1.2
NPSHA = 10.3 m
If the selected pump has:
NPSHR = 5.5 m
then the available margin is:
NPSH Margin = 10.3 − 5.5
NPSH Margin = 4.8 m
The final design should still be checked against manufacturer recommendations and the actual worst-case operating condition.
Boiler Feed Pump Power Calculation
After determining flow and total dynamic head, the next step is calculating the power required to operate the pump.
The calculation begins with hydraulic power.
Pump efficiency is then used to estimate shaft power.
Motor efficiency and operating margin can also be considered when selecting the motor.
Hydraulic Power Formula
In SI units:
Hydraulic Power = ρgQH
For kilowatts:
Hydraulic Power (kW) = ρgQH / 1000
Where:
ρ = fluid density in kg/m³
g = 9.81 m/s²
Q = flow in m³/s
H = head in meters
Pump Shaft Power
Pump shaft power is greater than hydraulic power because the pump has mechanical and hydraulic losses.
The formula is:
Shaft Power = Hydraulic Power ÷ Pump Efficiency
If:
Hydraulic power = 45 kW
Pump efficiency = 0.75
Then:
Shaft Power = 45 ÷ 0.75
Shaft Power = 60 kW
Pump Efficiency
Pump efficiency should ideally be taken from the actual pump performance curve.
Efficiency changes with flow.
The highest value usually occurs close to the best efficiency point.
Using an assumed efficiency can be useful during early calculations, but final motor sizing should use manufacturer data.
Motor Efficiency
The electrical motor also has losses.
If input electrical power is being estimated:
Electrical Input Power = Shaft Power ÷ Motor Efficiency
Suppose:
Shaft power = 60 kW
Motor efficiency = 95%
Then:
Electrical Input Power = 60 ÷ 0.95
Electrical Input Power ≈ 63.2 kW
Motor kW Calculation
Consider a feed pump operating at:
Flow = 40 m³/h
Head = 180 m
Density = 970 kg/m³
Pump efficiency = 78%
First convert flow:
40 m³/h ÷ 3600 = 0.0111 m³/s
Hydraulic power:
P = 970 × 9.81 × 0.0111 × 180 ÷ 1000
P ≈ 19.0 kW
Now calculate shaft power:
19.0 ÷ 0.78
Shaft Power ≈ 24.4 kW
The motor selected would need to safely handle the required shaft power across the intended operating range.
Motor HP Calculation
Kilowatts can be converted to horsepower using:
1 kW ≈ 1.341 hp
If shaft power is:
24.4 kW
then:
Motor Power ≈ 24.4 × 1.341
Motor Power ≈ 32.7 hp
The final motor rating should be selected from standard available sizes after considering pump curve requirements and engineering margin.
Selecting the Correct Motor Size
Motor selection should not be based only on the power required at one duty point.
The engineer should also check:
- Maximum pump power across the operating range
- Pump runout conditions
- Motor service factor where applicable
- Starting method
- VFD operation
- Ambient temperature
- Electrical supply
- Manufacturer recommendations
A motor that appears large enough at the normal operating point may still be overloaded if the pump moves to a higher-flow point on its curve.
Boiler Feed Pump Efficiency
Pump efficiency has a direct effect on energy use, motor size, operating cost, and long-term reliability.
A boiler feed pump may meet the required flow and head but still perform poorly if it operates far away from its most efficient region.
For this reason, efficiency should be checked together with flow, head, NPSH, and motor power.
Hydraulic Efficiency
Hydraulic efficiency represents how effectively the pump transfers energy to the liquid.
Some energy is lost because of internal flow disturbances, recirculation, leakage, and friction inside the pump.
A higher hydraulic efficiency means more of the input energy becomes useful fluid energy.
Mechanical Efficiency
Mechanical efficiency accounts for losses in bearings, seals, shaft components, and other moving parts.
These losses increase the amount of shaft power required to produce a given hydraulic output.
Overall Pump Efficiency
Overall pump efficiency combines the main internal losses of the pump.
It can be expressed as:
Pump Efficiency = Hydraulic Power ÷ Shaft Power
For example, if:
Hydraulic power = 30 kW
Shaft power = 40 kW
then:
Pump Efficiency = 30 ÷ 40
Pump Efficiency = 0.75 or 75%
This means 75% of the shaft power is converted into useful hydraulic power.
Best Efficiency Point
The best efficiency point, or BEP, is the operating point where the pump performs most efficiently.
At or near BEP, the pump generally experiences better hydraulic balance and lower internal losses.
Operating close to BEP can help reduce:
- Vibration
- Shaft loading
- Bearing wear
- Seal problems
- Recirculation
- Energy consumption
The exact acceptable operating range depends on pump design and manufacturer guidance.
How Efficiency Affects Motor Size
Lower pump efficiency means more shaft power is required.
Suppose the hydraulic power is:
50 kW
At 80% efficiency:
Shaft Power = 50 ÷ 0.80
Shaft Power = 62.5 kW
At 65% efficiency:
Shaft Power = 50 ÷ 0.65
Shaft Power ≈ 76.9 kW
The same hydraulic duty can therefore require a much larger motor when pump efficiency is poor.
Energy Cost of an Oversized Pump
An oversized boiler feed pump may operate at a flow much lower than its design point.
In systems with a control valve, the excess pump head may be wasted as pressure drop across the valve.
That means the motor consumes energy to create pressure that is then intentionally lost through throttling.
Correct pump sizing can reduce this unnecessary energy use.
Boiler Feed Pump Selection
Once the required flow, head, NPSH, and power are calculated, the next step is selecting an actual pump.
This is where the engineering calculation is matched against a manufacturer’s performance curve.
A pump should not be selected from flow capacity alone.
The complete duty point must be considered.
Determine Design Flow
Start with the maximum required feedwater flow including justified losses and design margin.
For example:
Design Flow = 28 m³/h
This becomes the horizontal flow coordinate on the pump curve.
Determine Total Dynamic Head
Next, calculate the total head the pump must produce.
Suppose:
TDH = 175 m
The preliminary duty point is now:
28 m³/h at 175 m head
These two values should be checked together on the pump curve.
Check NPSH
The selected pump will have a specific NPSHR at the design flow.
The actual system must provide enough NPSHA.
A pump that satisfies flow and head requirements but has excessive NPSHR may not be suitable.
Check Feedwater Temperature
The pump materials, seals, clearances, bearings, and suction characteristics must be suitable for the actual feedwater temperature.
High-temperature boiler feedwater requires more careful selection than cold-water service.
Check Pump Curve
The manufacturer’s pump curve normally shows:
- Flow
- Head
- Efficiency
- Power
- NPSHR
- Impeller diameter or stage configuration
The design duty point should fall within a suitable operating region of the curve.
Locate the Operating Point
The real operating point occurs where the pump curve intersects the system curve.
The pump curve shows what the pump can produce.
The system curve shows how much head the piping system requires at different flow rates.
Their intersection determines the actual flow and head during operation.
Check Best Efficiency Point
Once the operating point is located, compare it with the pump’s BEP.
A pump operating close to BEP is generally preferable to one that must run far to the left or right of its best efficiency region.
Select Motor Rating
The motor should be large enough to handle the pump’s maximum expected power demand.
The final selection should consider:
- Design duty
- Maximum operating flow
- Pump power curve
- Motor efficiency
- Starting conditions
- VFD requirements
- Manufacturer recommendations
Verify Materials of Construction
Boiler feedwater can be hot and chemically treated.
Pump materials must be suitable for the water chemistry, temperature, and pressure.
Typical material decisions may involve:
- Casing material
- Impeller material
- Shaft material
- Wear-ring material
- Mechanical seal material
The correct combination depends on the specific boiler system and pump design.
Understanding the Boiler Feed Pump Curve
A pump curve is one of the most important tools used during final boiler feed pump selection.
It shows how the pump behaves at different flow rates.
Understanding the curve helps prevent both undersizing and oversizing.
Flow vs Head Curve
The main curve shows the relationship between flow and head.
For many centrifugal pumps:
- Head is higher at low flow
- Head decreases as flow increases
The required design point should fall on or close to the selected pump curve.
Efficiency Curve
The efficiency curve shows how pump efficiency changes with flow.
The highest point is generally near the BEP.
Selecting a pump that operates close to this region can improve energy performance and reliability.
Power Curve
The power curve shows the shaft power required at different flow rates.
This curve is important when selecting the motor.
The motor should not become overloaded if the pump operates at a higher flow than the normal duty point.
NPSHR Curve
The NPSHR curve shows how much suction head the pump requires at different flow rates.
In many cases, NPSHR increases as flow rises.
This means a pump may have acceptable suction conditions at normal load but insufficient margin at maximum flow.
Best Efficiency Point
The BEP is typically marked near the peak of the efficiency curve.
Operating near this region generally improves:
- Efficiency
- Hydraulic stability
- Bearing life
- Seal life
- Vibration performance
Selecting the Correct Operating Point
Suppose the design requirement is:
30 m³/h at 160 m head
The selected pump should be able to provide this duty without operating near shutoff or extreme runout.
The point should also be reasonably close to the BEP.
Why the Duty Point Should Not Be Too Far From BEP
Operating far from BEP can increase internal hydraulic forces.
This can contribute to:
- Higher vibration
- Radial loading
- Internal recirculation
- Seal damage
- Bearing wear
- Reduced pump life
Good pump selection therefore considers not only whether the pump can reach the duty point, but how comfortably it operates there.
Boiler Feed Pump Sizing for Different Boiler Types
Boiler feed pump requirements can change depending on boiler design, operating pressure, steam capacity, and control system.
The basic calculation principles remain the same, but the final pump configuration may vary.
Fire-Tube Boiler Feed Pump Sizing
Fire-tube boilers are common in commercial and industrial steam systems.
Sizing normally focuses on:
- Steam capacity
- Boiler operating pressure
- Blowdown rate
- Feedwater temperature
- Required flow margin
Many lower-pressure fire-tube systems require less pump head than high-pressure water-tube systems.
Water-Tube Boiler Feed Pump Sizing
Water-tube boilers often operate at higher pressures and capacities.
This can result in:
- Higher pump discharge pressure
- Higher total dynamic head
- Greater motor power
- More demanding NPSH requirements
Multistage centrifugal pumps are commonly considered for higher-head applications.
Industrial Steam Boiler Feed Pump Sizing
Industrial steam plants may experience large changes in steam demand.
The feed pump therefore needs enough capacity to handle expected load variation.
Pump control may involve:
- Throttling valves
- Variable-speed drives
- Multiple pumps
- Automatic sequencing
High-Pressure Boiler Feed Pump Sizing
High-pressure boilers require pumps capable of producing substantial differential head.
The calculation should carefully include:
- Boiler pressure
- Economizer pressure drop
- Static head
- Control valve differential
- Pipe friction
- NPSH
- Pump power
Small mistakes become more significant when operating pressure is high.
Low-Pressure Boiler Feed Pump Sizing
Low-pressure boiler systems usually require less pump head.
However, flow, control stability, and suction conditions still need to be calculated properly.
A low-pressure boiler can still experience poor feedwater performance if the pump is incorrectly sized.
Package Boiler Feed Pump Sizing
Package boilers are supplied as compact systems and often come with recommended feedwater pump requirements.
Even so, site-specific conditions should be checked.
These can include:
- Feed tank elevation
- Feedwater temperature
- Piping length
- Control valve arrangement
- Economizer installation
Boiler Feed Pump Sizing by Boiler Capacity
Boiler capacity gives a useful starting point for feed pump sizing, but it should never be the only design value used.
Two boilers with the same steam capacity can require different pumps if their pressures and piping systems are different.
Feed Pump for Small Boilers
Small boilers may require relatively low flow rates.
Pump selection should still consider:
- Maximum boiler demand
- Minimum stable flow
- Boiler pressure
- Control method
- Standby requirements
A pump that is too large may cycle frequently or require excessive throttling.
Feed Pump for Medium Industrial Boilers
Medium industrial systems often require a balance between capacity, efficiency, and control flexibility.
A typical design process may include:
- Maximum steam load
- Blowdown
- Design margin
- Feedwater temperature
- TDH
- NPSH
- Pump curve review
Feed Pump for Large Boilers
Large boilers may require multiple feed pumps rather than one single unit.
Common arrangements can include:
- Duty and standby
- Two-duty and one-standby
- Parallel operation
This provides redundancy and greater control flexibility.
Feed Pump for High Steam Demand
High steam demand creates a high feedwater requirement.
However, a high-capacity pump also means higher suction velocity and potentially higher NPSHR.
The suction system must therefore be checked carefully when flow becomes large.
Boiler Horsepower to Feedwater Requirement
Boiler horsepower is still used for some boiler ratings, especially in North American applications.
It can be converted into approximate steam output, which can then be used to estimate feedwater demand.
What Is Boiler Horsepower?
Boiler horsepower is a traditional measure of boiler capacity.
One boiler horsepower is commonly associated with an evaporation rate of approximately:
34.5 lb/h of water from and at 212°F
This value can be used as a starting point when estimating steam output.
Boiler HP to Steam Capacity
A simplified relation is:
Steam Capacity (lb/h) ≈ Boiler HP × 34.5
For example:
Boiler capacity = 500 BHP
Then:
Steam Capacity ≈ 500 × 34.5
Steam Capacity ≈ 17,250 lb/h
This is a nominal conversion and actual boiler ratings should be checked against manufacturer data.
Boiler HP to Water Flow
Once the steam flow is estimated, feedwater demand can be calculated by adding blowdown and applicable losses.
Suppose:
Steam flow = 17,250 lb/h
Blowdown = 3%
Then:
Blowdown = 17,250 × 0.03
Blowdown ≈ 518 lb/h
So:
Feedwater Requirement ≈ 17,768 lb/h
A design margin may then be applied.
Example Boiler HP Feed Pump Calculation
Suppose a boiler is rated at:
800 BHP
Approximate steam production:
800 × 34.5 = 27,600 lb/h
Assume blowdown = 4%
Blowdown = 27,600 × 0.04
Blowdown = 1,104 lb/h
Operating feedwater:
27,600 + 1,104 = 28,704 lb/h
If a 10% design margin is used:
Design Feedwater = 28,704 × 1.10
Design Feedwater ≈ 31,574 lb/h
This mass flow can then be converted into GPM using the actual feedwater density.
Steam Capacity to Boiler Feedwater Flow
Many boiler feed pump calculations begin with the boiler’s maximum steam capacity.
Steam capacity may be given in several different units, so consistent conversion is important.
kg/h Steam to Feedwater Flow
If steam production is:
15,000 kg/h
and blowdown is:
3%
then:
Blowdown = 15,000 × 0.03 = 450 kg/h
Operating feedwater:
15,000 + 450 = 15,450 kg/h
lb/h Steam to Feedwater Flow
Suppose:
Steam production = 20,000 lb/h
Blowdown = 4%
Then:
Blowdown = 800 lb/h
Feedwater requirement:
20,800 lb/h
Additional margin can then be applied if required.
Ton/h Steam to Feedwater Flow
Suppose a boiler produces:
10 metric tons/h of steam
This is:
10,000 kg/h
If blowdown is 3%:
Blowdown = 300 kg/h
Operating feedwater:
10,300 kg/h
At a density of 960 kg/m³:
Volumetric Flow = 10,300 ÷ 960
Volumetric Flow ≈ 10.73 m³/h
Adding Blowdown and Design Margin
The complete simplified relationship is:
Design Feedwater = (Steam Flow + Blowdown + Other Losses) × Design Factor
This gives a more realistic pump sizing basis than using steam flow alone.
Metric Boiler Feed Pump Sizing Calculation
Metric calculations normally use:
- kg/h for mass flow
- m³/h for volumetric flow
- bar or kPa for pressure
- meters for head
- kW for power
Required Input Data
Assume the following design conditions:
Steam flow = 25,000 kg/h
Blowdown = 3%
Feedwater density = 965 kg/m³
Design factor = 1.10
Boiler pressure = 14 bar
Additional system head = 35 m
Pump efficiency = 78%
Calculate Feedwater Flow in kg/h
Blowdown:
25,000 × 0.03 = 750 kg/h
Operating feedwater:
25,000 + 750 = 25,750 kg/h
Design feedwater:
25,750 × 1.10 = 28,325 kg/h
Convert Flow to m³/h
Using:
Q = m ÷ ρ
Then:
Q = 28,325 ÷ 965
Q ≈ 29.35 m³/h
Calculate Pressure in Bar
Boiler operating pressure is:
14 bar
This is only the boiler pressure and not yet the complete pump requirement.
Calculate Head in Meters
For a preliminary approximation:
14 bar ≈ 142.8 m of water
Add system head:
TDH ≈ 142.8 + 35
TDH ≈ 177.8 m
Actual fluid density should be used for a more accurate pressure-to-head conversion.
Calculate Motor Power in kW
Convert flow:
29.35 ÷ 3600 ≈ 0.00815 m³/s
Assume:
Density = 965 kg/m³
Head = 177.8 m
Hydraulic power:
P = 965 × 9.81 × 0.00815 × 177.8 ÷ 1000
P ≈ 13.7 kW
Shaft power:
13.7 ÷ 0.78
Shaft Power ≈ 17.6 kW
The final motor size should be selected from the manufacturer’s pump and motor data.
Final Metric Pump Selection
The preliminary duty point is approximately:
Flow = 29.4 m³/h
Head = 178 m
This duty should then be checked against a suitable pump curve, NPSHR, efficiency, and motor power requirement.
Imperial Boiler Feed Pump Sizing Calculation
Imperial calculations typically use:
- lb/h for mass flow
- GPM for volumetric flow
- psi for pressure
- ft for head
- hp for power
Calculate Feedwater Flow in lb/h
Suppose:
Steam production = 30,000 lb/h
Blowdown = 3%
Then:
Blowdown = 900 lb/h
Operating feedwater:
30,900 lb/h
If design factor = 1.10
Then:
Design Feedwater = 33,990 lb/h
Convert Feedwater to GPM
The exact GPM depends on water density at the actual temperature.
As a simplified example, if feedwater density is approximately:
60 lb/ft³
Then volumetric flow is:
33,990 ÷ 60 = 566.5 ft³/h
Convert to gallons:
566.5 × 7.4805 ≈ 4,237 gal/h
Then:
GPM = 4,237 ÷ 60
GPM ≈ 70.6
Calculate Pressure in PSI
Suppose boiler pressure is:
180 psi
Additional system pressure requirement is:
25 psi
Then:
Required Differential Pressure ≈ 205 psi
Calculate Head in Feet
Using the approximate conversion:
1 psi ≈ 2.31 ft of water
Then:
Head ≈ 205 × 2.31
Head ≈ 474 ft
Calculate Pump Horsepower
A common water horsepower relationship is:
Hydraulic HP = Q × H × SG ÷ 3960
Where:
Q = GPM
H = head in feet
SG = specific gravity
Using:
Q = 70.6 GPM
H = 474 ft
SG ≈ 0.96
Then:
Hydraulic HP ≈ 70.6 × 474 × 0.96 ÷ 3960
Hydraulic HP ≈ 8.1 hp
If pump efficiency is 75%:
Shaft HP = 8.1 ÷ 0.75
Shaft HP ≈ 10.8 hp
The final motor should be selected based on actual manufacturer data.
Final Imperial Pump Selection
The preliminary duty point is approximately:
Flow = 71 GPM
Head = 474 ft
This point should then be checked on the selected pump curve.
Conclusion
A correct boiler feed pump sizing calculation is essential for reliable, efficient, and safe boiler operation. The pump must deliver enough feedwater to match steam production while also producing sufficient head to overcome boiler pressure, static elevation, pipe friction, control valves, economizers, and other system losses.
Accurate sizing starts with the required feedwater flow rate and continues through total dynamic head, discharge pressure, feedwater temperature, NPSH, pump efficiency, and motor power. These values should be considered together rather than selecting a pump based only on boiler capacity or operating pressure.
It is also important to avoid both undersizing and oversizing. An undersized boiler feed pump may struggle to maintain water level during high steam demand, while an oversized pump can waste energy, increase throttling, and operate far from its best efficiency point.
For the best results, use the calculated flow and head as the preliminary duty point, then verify the selection against the manufacturer’s pump curve, NPSHR, efficiency data, motor requirements, and actual site conditions. When these factors are properly evaluated, the boiler feedwater system can operate more smoothly, efficiently, and reliably over its full operating range.
FAQs
How do I calculate the size of a boiler feedwater pump?
To calculate the size of a boiler feedwater pump, first determine the required feedwater flow rate and total dynamic head. The flow rate should cover the boiler’s maximum steam production, blowdown losses, and a reasonable design margin. Then calculate the head needed to overcome boiler pressure, static elevation, pipe friction, control valves, economizers, and other system losses. After that, check NPSH and motor power before matching the duty point with a pump curve.
How to calculate pump sizing?
Pump sizing is mainly based on two values: required flow rate and total dynamic head. The flow rate tells you how much liquid the pump must move, while the total dynamic head tells you how much resistance the pump must overcome. A simplified relationship is: TDH = Static Head + Pressure Head + Friction Loss + Equipment Losses. Once flow and head are known, the pump should be selected from the manufacturer’s performance curve near a suitable efficiency range.
How to calculate the size of a boiler?
Boiler size is calculated from the required heating or steam load. For a steam boiler, the design usually starts with the maximum steam demand in kg/h, lb/h, or boiler horsepower. For heating applications, boiler capacity is based on the building or process heat requirement. The final boiler size should account for peak demand, system losses, operating conditions, and a suitable design allowance.
How to calculate the size of a heat pump?
Heat pump sizing is based on the heating and cooling load of the building. Important factors include floor area, insulation, climate, windows, air leakage, ceiling height, and indoor temperature requirements. A proper heat-loss and cooling-load calculation is more accurate than using only square-foot rules because an oversized or undersized heat pump can reduce comfort and efficiency.
What is the TDS limit for boiler feed water?
There is no single TDS limit that applies to every boiler. The acceptable level depends on boiler pressure, boiler type, treatment program, and manufacturer requirements. Lower-pressure boilers can generally tolerate higher dissolved solids than high-pressure boilers, while high-pressure systems require much cleaner feedwater. Feedwater quality should therefore be checked against the boiler manufacturer’s specifications and the water-treatment program rather than relying on one universal ppm value.
What type of pump is used for boiler feedwater?
Centrifugal pumps are commonly used for boiler feedwater service. High-pressure boiler systems often use multistage centrifugal pumps because several impellers arranged in stages can generate the high head needed to force feedwater into a pressurized boiler. The final pump type depends on boiler pressure, flow rate, feedwater temperature, NPSH, and operating requirements.
What is the boiler formula?
There is no single boiler formula because different calculations are used for capacity, efficiency, steam generation, fuel consumption, and feedwater demand. For boiler feedwater, a simple mass-balance relationship is: Feedwater Flow = Steam Flow + Blowdown Flow + Other Continuous Losses. Boiler efficiency is commonly expressed as useful heat output divided by heat input, multiplied by 100.
How do you size pumps?
Pumps are sized by identifying the required flow rate and the total dynamic head of the system. The next steps are to check fluid properties, operating temperature, suction conditions, NPSH, pump efficiency, and power requirement. The calculated duty point is then compared with a manufacturer’s pump curve. A good selection should meet the required flow and head without operating too far from the pump’s best efficiency point.
